Identification Information

Title Santa Fe County, 2018 NC NAIP Ortho Mosaic

Date 2019-05-02

Date Type Publication

Cited Responsible Party

Organization Name USDA-FSA-APFO

Role identify

Presentation Form

Abstract This data set contains imagery from the National Agriculture Imagery Program (NAIP). The NAIP acquires digital ortho imagery during the agricultural growing seasons in the continental U.S. A primary goal of the NAIP program is to enable availability of ortho imagery within one year of acquisition. The NAIP provides 60 centimeter ground sample distance (GSD) ortho imagery rectified to a horizontal accuracy within +/- 4 meters of reference digital ortho quarter quads (DOQQ's) from the National Digital Ortho Program (NDOP) or from the National Agriculture Imagery Program (NAIP). The tiling format of NAIP imagery is based on a 3.75' x 3.75' quarter quadrangle with a 300 pixel buffer on all four sides. The NAIP imagery is formatted to the UTM coordinate system using the North American Datum of 1983 (NAD83). The NAIP imagery may contain as much as 10% cloud cover per tile. This file was generated by compressing NAIP imagery that cover the county extent. Two types of compression may be used for NAIP imagery: MrSID and JPEG 2000. The target value for the compression ratio is 40:1 for imagery.

Purpose The NAIP imagery is typically available for distribution within 60 days of the end of a flying season and is intended to provide current information of agricultural conditions in support of USDA farm programs. For USDA Farm Service Agency, the 1 meter and 1/2 meter GSD product provides an ortho image base for Common Land Unit boundaries and other data sets. The NAIP imagery is generally acquired in projects covering full states in cooperation with state government and other federal agencies who use the imagery for a variety of purposes including land use planning and natural resource assessment. The NAIP is also used for disaster response often providing the most current pre-event imagery.

Status Complete

Point of Contact

Individual Name

Organization Name USDA-FSA Aerial Photography Field Office

Position Name

Role Point of contact

Voice 801-844-2900

Facsimile

Address

Delivery Point 2222 West 2300 South
City Salt Lake City
Administrative Area Utah
Postal Code 84119-2020
Country USA

Electronic Mail Address

Maintenance and Update Frequency Irregular

Descriptive Keywords imageryBaseMapsEarthCover, farming, Digital Ortho rectified Image, Mosaic, Quarter Quadrangle, Ortho Rectification, Compression, MrSID, JPEG 2000, NAIP, Compliance, Aerial Compliance

Access Constraints There are no limitations for access.

Use Constraints None, The USDA-FSA Aerial Photography Field Office asks tobe credited in derived products. If defects are found in the NAIP imagery during the 1 year warranty period such as horizontal offsets, replacement imagery may be provided. Imagery containing defects that require the acquisition of new imagery, such as excessive cloud cover, specular reflectance, etc., will not be replaced within a NAIP project year.

Language English

Topic Category

Extent

Geographic Bounding Box

West Bound -106.268261
East Bound -105.676794
North Bound 36.062456
South Bound 34.998699

Temporal Extent

DateTime 2018

Data Quality Information

Horizontal Positional Accuracy Report

Report FSA Digital Orthophoto Specs.

Quantitative Horizontal Positional Accuracy Assessment

Horizontal Positional Accuracy Value
Horizontal Positional Accuracy Explanation

Vertical Positional Accuracy Report

Report N/A 2d only

Quantitative Vertical Positional Accuracy Assessment

Vertical Positional Accuracy Value
Vertical Positional Accuracy Explanation

Logical Consistency Report NAIP 3.75 minute tile file names are based on the USGS quadrangle naming convention.

Completeness Report None

Lineage

Process Step

Process Description Digital imagery was collected at a nominal GSD of 40cm using 10 Cessna 441’s, one Cessna 414, one Reims F406, three Piper PA31’s, one Piper PAY2 and one Swearingen Merlin-3 aircraft flying at an average flight height of 8400m AGL for the SH120 acquisition and 4400m AGL for SH100 acquisition. Aircraft flew with Leica Geosystem's ADS100/SH100 digital sensors with firmware 4.57 or ADS100/SH120 digital sensors with firmware 4.57. Each sensor collected 12 image bands Red, Green, Blue and Near-infrared at each of three look angles; Backward 19 degrees, Forward 26 degrees and Nadir for the SH100. Backward 10 degrees, Forward 14 degrees, and Nadir for the SH120. The Nadir Green band was collected in high resolution mode effectively doubling the resolution for that band. The ADS100 spectral ranges are; Red 619-651nm, Green 525-585nm, Blue 435-495nm and Near-infrared at 808-882nm. The CCD arrays have a pixel size of 5.0 microns in a 20000x1 format at nadir; a 18000x1 format at the backward look angle and a 16000x1 format at the forward look angle. The CCD's have a dynamic range of 72db and the A/D converters have a resolution of 14bits. The ADS is a push-broom sensor the ground footprint of the imagery is approximately 8km wide at a nominal 40cm GSD by the length flightline. The maximum flightline length is limited to approximately 175km. The factory calibrations and IMU alignments for each sensor (Serial Numbers: 10510, 10511, 10512, 10514, 10519, 10552, 10522, 10527, 10528, 10530, 10531, 10534, 10537, 10540, 10554, 12529) were tested and verified by in-situ test flights before the start of the project. The Leica MissionPro Flight Planning Software is used to develop the flight acquisition plans. Flight acquisition sub blocks are designed first to define the GNSS base station logistics, and to break the project up into manageable acquisition units. The flight acquisition sub blocks are designed based on the specified acquisition season, native UTM zone of the DOQQs, flight line length limitations (to ensure sufficient performance of the IMU solution) as well as air traffic restrictions in the area. Once the sub blocks have been delineated they are brought into MissionPro for flight line design. The design parameters used in MissionPro will be 30% lateral overlap and 40cm resolution. The flight lines have been designed with a north/south orientation or east/west where required for efficiency. The design takes into account the latitude of the state, which affects line spacing due to convergence as well as the terrain. SRTM elevation data is used in the MissionPro design to ensure the 50cm GSD is achieved over all types of terrain. The raw data was downloaded from the sensors after each flight using Leica XPro software. The imagery was then georeferenced using the 200Hz GPS/INS data creating an exterior orientation for each scan line (x/y/z/o/p/k). Leica Xpro APM software was used to automatically generate tiepoint measurements between the forward, nadir and backward look angles for each line and to tie all flight lines together. The resulting point data and exterior orientation data were used to perform a full bundle adjustment using ORIMA software. Blunders were removed, and additional tie points measured in weak areas to ensure a robust solution. Once the point data was clean and point coverage was acceptable, photo-identifiable GPS-surveyed ground control points were introduced into the block adjustment. The bundle adjustment process produces revised exterior orientation data for the sensor with GPS/INS, datum, and sensor calibration errors modeled and removed. Using the revised exterior orientation from the bundle adjustment, orthorectified image strips were created with Xpro software and the June 2018 USGS 10m NED DEM. The Xpro orthorectification software applies an atmospheric-BRDF radiometric correction to the imagery. This correction compensates for atmospheric absorption, solar illumination angle and bi-directional reflectance. The orthorectified strips were then overlaid with each other and the ground control to check accuracy. Once the accuracy of the orthorectified image strips were validated the strips were then imported into Inpho's OrthoVista 7.1.2 package which was used for the final radiometric balance, mosaic, and DOQQ sheet creation. The final DOQQ sheets, with a 300m buffer and a ground pixel resolution of 60cm were then combined and compressed to create the county wide CCMs.
Process Date 2019-02-11
Process Time
Process Contact

Santa Fe County, 2018 NC NAIP Ortho Mosaic

Metadata from the RGIS Metadata Repository

Identification Information

Distribution Information

Spatial Reference Information

Data Quality Information

Metadata Reference Information